Module 
COLOR TYPE -TRT
240 x RGB(H) x 320(V)        TFT (2.4 inch) Model : EDG024A01TOXGB
DIMENSIONAL DRAWING DOWNLOAD    form in PDF format
FEATURE : BLOCK DIAGRAM
  1. Display Mode: TFT(2.4 inch)/Transmissive/
    Negative
  2. Driving voltage: VDD=2.8V
  3. Viewing direction: 12 O'Clock
  4. Operating temp: -20C~+70C
    Storage temp: -30C~+80C
  5. Interface: 80 PARALLEL
  6. Unmarked tolerance: +0.2mm
  7. Backlight: White
  8. ROHS request: YES
ELECTRO-OPTICAL CHARACTERISTICS
ITEM SYMBOL CONDITIONS MIN TYPE MAX UNIT REMARK
Esponse time Rise Tr =0 - 12 - ms Note4
Fall Tf - 18 - ms
Contrast ratio CR At optimize viewing angle 250 300 - - Note5
Transmilttance %     6.0   %  
Viewing Angle Top --- CR5 40 60 - deg. Note6
Bottom 10 20 -
Left 30 45 -
Right 30 45 -
Color Tone White Wx =0 0.26 0.31 0.36 -  
Wy 0.28 0.33 0.38

Input/Output Signal Interface

NO PIN name I/O Description NO PIN name I/O Description
1

A

PI

Anode of LED

17

DB8

I An 18-bit parallel bi-directional data bus for MPU system interface mode.8-bit I/F: DB[17:10] is used.9-bit I/F: DB[17:9] is used.16-bit I/F: DB[17:10] and DB[8:1] is used.18-bit I/F: DB[17:0] is used.18-bit parallel bi-directional data bus for RGB interface operation.6-bit RGB I/F: DB[17:12] are used.16-bit RGB I/F: DB[17:13] and DB[11:1] are used.18-bit RGB I/F: DB[17:1] are used.
2

K

PI Cathode of LED 18

DB9

I
3

VCI

PI

Analog power input, 2.4~3.3V is recommended.

19

DB10

I
4

IOVCC

PI

Digital power input, 1.65~3.3V is recommended.

20

DB11

I
5 CS I A chip select signal.Low: the chip is selected and accessible.High: the chip is not selected and not accessible 21 DB12 I
6

RS

I A register select signal.Low: select an index or status register.High: select a control register 22

DB13

I
7 WR I A write strobe signal and enables an operation to write data.when the signal is low. 23

DB14

I
8 RD I A read strobe signal and enables an operation to read out data.when the signal is low. 24

DB15

I
9

DB0

I An 18-bit parallel bi-directional data bus for MPU system interface mode.8-bit I/F: DB[17:10] is used.9-bit I/F: DB[17:9] is used.16-bit I/F: DB[17:10] and DB[8:1] is used.18-bit I/F: DB[17:0] is used.18-bit parallel bi-directional data bus for RGB interface operation.6-bit RGB I/F: DB[17:12] are used.16-bit RGB I/F: DB[17:13] and DB[11:1] are used.18-bit RGB I/F: DB[17:1] are used. 25

DB16

I
10

DB1

I 26 DB17 I
11

DB2

I 27

ENABLE

I

Data ENEABLE signal for RGB interface operation.Low: Select (access enabled) High: Not select (access inhibited)

12

DB3

I 28

DCLK

I Dot clock
13 DB4 I 29 HSYNC I Horizontal synchronous signal
14 DB5 I 30 VSYNC I Vertical synchronous signal
15 DB6 I 31 RESET I Global reset
16 DB7 I 32 VSS G Ground